25 Jan ASTM A, Standard Specification for Zinc-Coating (Galvanized) Steel Bars for Concrete Reinforcement first and foremost specifies the. ASTM A/AM: Standard Specification for Zinc-Coated (Galvanized) Steel Bars for Concrete Reinforcement. ASTM A – Download as PDF File .pdf), Text File .txt) or read online. ASTM A

Author: Mokree Kagara
Country: Martinique
Language: English (Spanish)
Genre: History
Published (Last): 15 February 2012
Pages: 310
PDF File Size: 10.44 Mb
ePub File Size: 3.98 Mb
ISBN: 541-2-54321-550-2
Downloads: 84598
Price: Free* [*Free Regsitration Required]
Uploader: Zulkitilar

Anyone making use of this information assumes all liability arising from such use. Combining values from the two systems may result in non-conformance with this specification. Number 12 and smaller bar must have a minimum of 3. January 25, Authored by Dr.

ASTM A767 for Reinforcing Steel

The information provided herein is not intended as a representation or warranty on the part of the AGA. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents. This specification also introduces a new requirement to the galvanized coating known as chromating.

ASTM A767 – Galvanizing Steel Bars for Concrete Reinforcement – Rebar

It is important to note reinforcing steel used in conjunction with structural steel, welded to a fabricated assembly is not governed by ASTM A but rather ASTM A, the standard specification for zinc coatings on iron and steel products. The material provided herein has been developed to provide accurate and authoritative information about after-fabrication hot-dip galvanized steel.

Therefore, each system shall be used independently of the other. Unique to this specification is also the requirement the galvanized bars be immersed in a heated, sodium dichromate solution immediately after the process.

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.


However, wire is not included. The specification also calls out specific recommended before galvanizing bending radii. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. Rebar is commonly bent prior to the hot-dip galvanizing process.

This post-treatment helps to prevent the formation of wet storage stain on the bars when they are in bundles at a job site and also promotes good adhesion of the galvanized rebar to the concrete it is placed in.

These notes and footnotes excluding those in tables shall not be considered as requirements of the specification. Work Item s – proposed revisions of this standard. This cold working of the bars s767 induced stresses that may be released after the bars are immersed in the molten F zinc bath. In addition, since rebar is handled frequently during its installation, any tears or sharp spikes that make the material dangerous to handle are grounds for rejection.

Steel reinforcing bars bent cold prior to hot-dip galvanizing should be fabricated to a bend diameter equal to or greater than the specified values. The mass of zinc coating shall conform to specified requirements.

Historical Version s – view previous versions of standard Work Item s – proposed revisions of this standard Translated Version s: The galvanized coating shall be chromate treated. Stripping method, weighing before and after galvanizing, and microscopy method shall be used to referee the results obtained by magnetic thickness measurements.

A retest shall be provided if the average zinc coating mass fails to meet the requirements. The mass of the coating shall be determined by magnetic thickness gage measurements.

ASTM A for Reinforcing Steel | American Galvanizer’s Association

The galvanizer is identified throughout this specification as the manufacturer. Newly galvanized steel can react with wet asfm and potentially form hydrogen gas as a product.


This material provides general information only and is not intended as a substitute for competent professional examination and verification as to suitability and applicability.

Galvanization shall be used to prepare reinforcing bars. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided asfm part of the standard.

ASTM A – Galvanizing Steel Bars | American Galvanizer’s Association

This specification covers steel reinforcing bars with protective zinc coatings applied by dipping the properly prepared reinforcing bars into a molten bath of zinc. Link to Active This link will always route zstm the current Active version of the standard. Was this answer helpful? As this evolved hydrogen gas travels through the concrete matrix toward the surface, voids can be created which weaken the bonding with the concrete or disturb the smoothness of the asrm surface.

Are you still looking for the right answer? The galvanizer shall be permitted to subject the newly coated steel reinforcing bars to air or steam wiping to remove excess zinc from the bars. However, this single product specification introduces a few new requirements that apply solely to hot-dip galvanized rebar. In order to help prevent and suppress this asrm, hot-dip galvanized rebar is dipped into a dilute chromate quench solution after being removed from the galvanizing kettle.

Table 5 below gives recommendations for bend diameters based upon the bare steel bar diameter before coating. Leave this field blank. This abstract is a brief summary of the referenced standard. Historical Version s – view previous versions of standard.