Section 11 of ASTM F details the requirements of each report, including test hole location, dates and times of measurements, RH reading, temperature. Last previous edition approved in as. F DOI: / F/FA. 2 For referenced ASTM standards, visit the ASTM . ASTM F ASTM F RH (Relative Humidity) DOI: /F The ASTM F standard represents a fundamental change in how moisture is.
|Published (Last):||22 November 2017|
|PDF File Size:||15.98 Mb|
|ePub File Size:||20.90 Mb|
|Price:||Free* [*Free Regsitration Required]|
The depth is calculated to the bottom of the test hole the location of the installed RH sensor or probe. April 3, at Note that the liner requirements have been updated and the hole is to be fully lined to meet wstm ASTM standard. The Ligno-Tec RH was designed for reliability and accuracy as well as sturdiness and ease of operation. December 27, at 3: In that case, builders did not allow the slab sufficient time for concrete moisture levels to equilibrate reach equilibrium moisture content according to relative humidity RH.
All sensors must be calibrated no less than 30 days prior to use. January 9, at Preparation Confirm your test method equipment meets specifications. Map your sensor count and location. The RH BluePeg probe drops easily into the sleeve.
Now is a good time to buy! Be sure to familiarize yourself with ASTM F and choose the best concrete moisture test method for f2170-111 job. Depress SET Button to check settings.
Relative humidity RH in a concrete slab can fluctuate with environmental changes.
It has been believed that the change in the 2f170-11 weight could be translated into a moisture ratio for the concrete beneath. This process requires time and quantifiable concrete moisture measurements to verify. The first thing I would look at is the assembly that you are installing. When concrete is mixed and poured, water vapor migrates from the bottom of the slab to the surface to evaporate.
If you forward to 1: April 7, at 3: How do you handle this problem? As concrete dries, moisture migrates from the bottom of the slab to the surface where it can evaporate away.
Ligno-Tec RH Concrete Test Conforms to ASTM F
Reusable sensors should be calibrated by the manufacturer at least once per year, or more often if exposed to conditions that may impact their accuracy. First, I have to state that F is specified f2170-1 interior applications that are under consistent ambient air controls. The RH BluePeg probe f2170-1 a hi-accuracy sensor with a short acclimation time.
Without studying pages and pages of operation manuals: September 6, at Use up or down buttons to correct settings.
Ligno-Tec RH Concrete Moisture Meter
Jason, I appreciate this means to contact you. Surface-based test results will fluctuate, even more, under these changes in environmental conditions.
The instruments have proven to perform well in rough mill environments with day-to-day usage. In this way, in situ measurement provides a composite picture of overall slab moisture levels, and provides the data necessary to make business r2170-11 regarding flooring installations. At this point, if one test fails, they all fail. Logically then, moisture levels at the bottom of a slab will read higher ast those at the surface.
Each hole must have a liner that isolates the sensor from ambient conditions, and sensors must have NIST-traceable calibration. After the initial reading, readings can be updated at any time desired with two conditions in mind: Leave a Reply Cancel reply Your email address will not be published. Thanks for the reply, Patrick.
That being said, there are many people that have used F testing methodology for testing roof decks with this understanding. These requirements for the standard apply regardless astk the RH test method being used.
General contractors must bear in mind two interactive processes when they are looking at construction schedules: If longer sleeves are desired we also offer 3. Without it, even a well-dried and functioning foundation can end up with concrete slab moisture problems. October 31, at Many contractors use vapor barriers directly under the slab to slow moisture permeation.
All cables have easy-to-connect and fail-proof 35mm stereo connectors.
10 Guidelines for ASTM F Compliance
And installers are finding results are more accurate and more dependable with RH testing. That being said, I have heard a couple of different methods people are using.
While any professional must understand the exact requirements of standard F the most recent versionthe following are 10 guidelines to help ensure that you have met the criteria laid out in ASTM F Each test hole must be drilled to the depth determined at Step 5 above section 10 of ASTM F and properly prepared.
You consent to our cookies if you continue to use our website.